V8매니아 로고
V8 Mania 자료실 커뮤니티 오픈마켓

튜닝자료실

카마로ss와 관련된 튜닝자료를 공유합니다.

Home > 자료실 > 튜닝자료실

혹시나 Lt4 슈퍼차져를 올릴려면 필요한것들 튜닝자료실 -카마로ss동호회

혹시나 Lt4 슈퍼차져를 올릴려면 필요한것들

김도영(SunShine)  |  조회수 :3643  |  2022-02-18 (20:35)

Mechanical Parts need to mount and run a PD blower:

Intake tube GM 22935828
Crank Pulley/Balancer GM 12671006 or 12687725
Crank Balancer Bolt GM 11547373
Tensioner GM 12663624
Pulley GM 12665845
Pulley Idler GM12642705
Pulley Idler GM12642707
ICT Billet Adapter LT1 Heads to LT4 intake ICT# 551590
GM Balancer w/ 3.50 blower puller 84.8" belt K408048
LT4 Valley cover AKA valve AFM lifter masnifold #12699793, 12675782, & 12674051 You can block off hole on the bottom of the blower

Easiest way to handle the intercooler system:

Intercooler pump with bracket Edelbrock number #51-4201
Intercooler Pump LT4/CTS-V GM #13597903
Intercooler water pump harness that Ts into the Evap #37-6619 or a lingenfelter L480340000 you will need to still to add a relay and wire the intercooler pump up
PLM Exchanger 350 for sock thickness and 395 for 2 inch plus thichness
3/4 Hose and preformed elbows by gates I leave this to you, you can setup
your I/C system how you want
ADM setup: sourced out: Parts used to mount the reservoir and mate to stock I/C hoses for and LT4
Gates 19839 premolded heater hose U will cut and route $10.00 Orileys
Gates 28479 premolded heater hose U will cut and route $10.00 Orileys
2 5/8 to 3/4 coupler $1.99
2 24mm constant tension spring hose clamps These are black look better $1.00 ea
6 26mm constant tension spring hose clamps $1.00
Edelbrock 51-7100 Tank – black reservoir like Magi or ADM $27.00
Edelbrock 51-7008 Tank lid - $13.00
Edelbrock 79-9177 Tank bracket - needs a bit of mods to attach to strut $35.00
SS reservoir install https://www.camaro6.com/forums/showthread.php?t=553155

Electrical System: T MAP MAF Harness..

Edelbrock # 37-1619 * for this map (0261230042) 2.5 bar
DSX harness dave can make harness if you tell which map you plan to use.


I will continue to updat..

$159.00 ZZP LT4 SC pulley 2.7 - to 2.8 depending on fuel mods
$350.00 12671006, 12687725, 12713718 LT4 Balancer (ATI ATI918856 & 916153 $475.00) for 100 more I would do this option
$238.00 12699793 LT4 valley cover or block of the PCV port
$54.00 12692675 Bracket for ZL1/CTS
$54.00 12663624 Belt tensioner with 8 rib Zl1
$43.00 12678515 8 rib Zl1 96mm pulley
$53.00 12678295 8 rib ZL1 77mm pulley
$55.00 12665845 8 rib smooth pulley ZL1
$23.00 12585673 LS3 front cover seal
2x Bolt, Hex Flange, M10 x 100mm
2x Bolt, Hex Flange, M8 x 55mm
3x Bolt, Hex Flange, M8 x 40mm
$219.00 551590 ICT Billet LT1 to LT4 Adapter
37-1605 Edelbrock water pump harness that's activated by the evap solenoid
37-6619 Edelbrock Baro harness for the MAF/TMAP
$395.00 PLM-HE-CH-CA-2017 PLM exchanger
$649.00 LPE L300227415 Bumper reservoir
$490.00 E2512A Stewart EMP intercooler pump (1 inch so you will need 1 in to 3/4 fitting to reduce. however there will be no 5/8 fittings on the car since like the zl1 so you will be way better off.



현재로써는 가장 저렴하게 슈퍼차져를 올릴수있는방법같습니다.


미국 사이트에서 lt4 차져는 대략 1500불정도에 거래가되는거같고


차져 단품만 업글하고 파는것이라 나머지 부품들이 필요한데


위와같습니다.


정 귀찮으면 한방에 모아서 파는 싸이트도 있습니다만 각각 구하는게 쌀듯




  • 김상필(서해) | 2022-02-19 00:09
암만 순정 챠져라고 해도 프로그램 튜닝등등은 할수 없겟지요???

순정 프로그램도 팔라나요??? 단순 부품만 교체 한다고 끝이 아닐듯한데요
  •  김도영(SunShine) | 2022-02-19 15:29
       맵은 따로 해야겠죠 ㅎㅎ
  • 김덕훈(밍구아빠) | 2022-02-19 20:47
제대로 된 비용 지불하고 샾에 맡기는 것이 가장 좋은 방법일지도 ㅎㅎ
번호 제목 작성자 등록일 조회수
607 카마로 ss 볼트온킷 다이노 테스트 영상  [4]
김도영(SunShine) I 2023-09-10 (22:05) I 조회: 3714
김도영(SunShine) 2023-09-10 (22:05) 3714
606 Hptuner - #9 PE 모드의 조정(연료)  [1]
김도영(SunShine) I 2023-08-16 (11:03) I 조회: 3854
김도영(SunShine) 2023-08-16 (11:03) 3854
605 Hptuner - #8 Tire Calibration  [3]
김도영(SunShine) I 2023-07-27 (14:54) I 조회: 3685
김도영(SunShine) 2023-07-27 (14:54) 3685
604 Hptuner - #7 토크 리밋 해제
김도영(SunShine) I 2023-07-27 (14:01) I 조회: 3679
김도영(SunShine) 2023-07-27 (14:01) 3679
603 Hptuner - #6 Driver Demand (스로틀 민감도 조정)  [3]
김도영(SunShine) I 2023-07-27 (13:54) I 조회: 3683
김도영(SunShine) 2023-07-27 (13:54) 3683
602 Hptuner - #5 V4 모드를 꺼보자~ Dod off  [3]
김도영(SunShine) I 2023-06-22 (09:14) I 조회: 3637
김도영(SunShine) 2023-06-22 (09:14) 3637
601 PD blower(위플, 맥너슨) 사용자글을 위한 팁?  [1]
김도영(SunShine) I 2023-06-20 (21:44) I 조회: 3644
김도영(SunShine) 2023-06-20 (21:44) 3644
600 Lt1 엔진 Issue #2
김도영(SunShine) I 2023-06-05 (11:03) I 조회: 3642
김도영(SunShine) 2023-06-05 (11:03) 3642
599 아는사람에게는 유용한 정보인 BOB Weight   [1]
김도영(SunShine) I 2023-06-05 (10:47) I 조회: 3639
김도영(SunShine) 2023-06-05 (10:47) 3639
598 각종 슈퍼차져 레이아웃.  [1]
김도영(SunShine) I 2023-05-29 (17:30) I 조회: 3641
김도영(SunShine) 2023-05-29 (17:30) 3641
597 2300 맥너슨 슈퍼차져.SC Lid 메탄노즐분사
김도영(SunShine) I 2023-05-29 (17:23) I 조회: 3639
김도영(SunShine) 2023-05-29 (17:23) 3639
596 112mm throttle spacer for Whipple 3.0  [1]
김도영(SunShine) I 2023-04-15 (11:24) I 조회: 3640
김도영(SunShine) 2023-04-15 (11:24) 3640
595 Lt1 엔진 Issue #1  [3]
김도영(SunShine) I 2023-03-16 (17:10) I 조회: 3652
김도영(SunShine) 2023-03-16 (17:10) 3652
594 위플 차져 보닛 간섭 확인 ^^
김도영(SunShine) I 2023-03-16 (09:51) I 조회: 3640
김도영(SunShine) 2023-03-16 (09:51) 3640
593 슈퍼차져 메탄 포트분사.  [3]
김도영(SunShine) I 2023-02-08 (15:21) I 조회: 3640
김도영(SunShine) 2023-02-08 (15:21) 3640
592 2300 기본킷 후기  [7]
정영준(정월리) I 2023-02-03 (22:51) I 조회: 3653
정영준(정월리) 2023-02-03 (22:51) 3653
591 아래글에 이어 하이캠 St0.5 사운드  [2]
구본민(구본민) I 2022-11-29 (08:53) I 조회: 3637
구본민(구본민) 2022-11-29 (08:53) 3637
590 하이켐 St1 vs St2 사운드  [2]
김도영(SunShine) I 2022-11-28 (18:01) I 조회: 3646
김도영(SunShine) 2022-11-28 (18:01) 3646
589 신형 위플 Gen5 3.0 슈퍼차져.  [2]
김도영(SunShine) I 2022-11-28 (16:54) I 조회: 3643
김도영(SunShine) 2022-11-28 (16:54) 3643
588 Billet 써모 하우징  [1]
김도영(SunShine) I 2022-10-28 (20:39) I 조회: 3643
김도영(SunShine) 2022-10-28 (20:39) 3643